Skip to Content

Changes for page Front I/O

Last modified by Kevin Wiki on 2024/07/07 22:48
From version 2.3
edited by Kevin Wiki
on 2024/07/04 18:14
Change comment: There is no comment for this version
To version 4.1
edited by Kevin Wiki
on 2024/07/04 23:07
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -6,19 +6,11 @@
6 6  
7 7  There is a single cable that controls four parts, each half side of I/O LED and center column of blue LEDs.
8 8  
9 -== Sub-paragraph ==
9 +[[image:xserve io main cable pinout.drawio.png]]
10 10  
11 -Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Excepteur sint occaecat cupidatat non proident, sunt in culpa qui officia deserunt mollit anim id est laborum.
11 +(% class="wikigeneratedid" %)
12 +[[attach:xserve io main cable pinout.drawio.svg||target="_blank"]]
12 12  
13 -== Sub-paragraph ==
14 -
15 -Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Excepteur sint occaecat cupidatat non proident, sunt in culpa qui officia deserunt mollit anim id est laborum.
16 -
17 -=== Sub-sub paragraph ===
18 -
19 -Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Excepteur sint occaecat cupidatat non proident, sunt in culpa qui officia deserunt mollit anim id est laborum.
20 -
21 -
22 22  = How we got here =
23 23  
24 24  Measure out the ground and power signals by comparing with other chips on board. E.g. we find [SAA1064T] datasheet, locate the GND (Vee) and 5V (Vcc) and measure connectivity (0 ohm resistance) between chip pins and cable pins. This gives us pins GND 2 & 8 and PWR 16 & 22.
... ... @@ -151,25 +151,47 @@
151 151  }
152 152  {{/code}}
153 153  
146 +== SAA1064T data for driving center IO LED stack ==
147 +
148 +Center IO stack is a stack of 23 LED's, 22 blue and 1 green for ethernet activity. These are duplicated next to each other and driven by each their SAA1064T chips. Earlier we found the i2c address and just by playing around figured out that 4 segments of 1 byte binary values are used to set ship register.
149 +
150 +{{code language="C++"}}
151 +void fillColumns() {
152 + Serial.println("filling columns");
153 + Wire.beginTransmission(saa1064);
154 + Wire.write(1);
155 + Wire.write(0x7F); // 127 - 1111111
156 + Wire.write(0x7F); // 127 - 1111111
157 + Wire.write(0x7F); // 127 - 1111111
158 + Wire.write(0x1F); // 31 - 11111
159 + Wire.endTransmission();
160 +
161 + colsFilled = 1;
162 +}
163 +{{/code}}
164 +
165 +(% class="wikigeneratedid" %)
166 +Here the last byte we send only is 5 bits since we only have 5 LEDs instead of 6 to address (total of 23). Also note that we start the transmission with a single bit.
167 +
154 154  == Pinouts voltages from MLB ==
155 155  
156 156  Powered off:
157 157  
158 158  * PWR fail LED - 0.00 V
173 +* UID LED - 4.5V
159 159  * OH/Fan fail LED - 4.72 V
160 160  * NIC1 LED - 0.8 - 2.6 V
161 161  * NIC2 LED - 2.95 V
177 +* UID SW - 2.8V
162 162  * HDD LED - 0.00 V
163 -* Power LED - 0.00 V after unplug grows
164 164  * Power LED P3V3 - 0.00V
165 -* UID SW - 2.8V
166 -* UID LED - 4.5V
180 +* Power LED - 0.00 V after unplug grows
167 167  
168 168  Powered on:
169 169  
170 170  * PWR tail LED - 3.47 V
171 -* OH/Fan failed LED - 5 V
172 172  * UID LED - 4.85V
186 +* OH/Fan failed LED - 5 V
173 173  * NIC 1 LED - 1.2 - 2.9 V
174 174  * NIC 2 LED - 3.2 V
175 175  * UID SW - 3V
... ... @@ -177,7 +177,6 @@
177 177  * Power LED P3V3 - 3.30V
178 178  * Power LED - 0.87 V
179 179  
180 -
181 181  
182 182  )))
183 183  
... ... @@ -199,5 +199,6 @@
199 199  
200 200  
201 201  
215 +
202 202  )))
203 203  )))
xserve io main cable pinout.drawio.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.kevin
Size
... ... @@ -1,0 +1,1 @@
1 +41.4 KB
Content
xserve io main cable pinout.drawio.svg
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.kevin
Size
... ... @@ -1,0 +1,1 @@
1 +41.4 KB
Content