Front I/O - XWiki

1

(% class="row" %)

2

(((

3

(% class="col-xs-12 col-sm-8" %)

(((

= Pinout =

There is a single cable that controls four parts, each half side of I/O LED and center column of blue LEDs.

8

9

[[image:xserve io main cable and PCB pinout.drawio.png||alt="xserve io main cable pinout.drawio.png"]]

10

11

(% class="wikigeneratedid" %)

12

[[attach:xserve io main cable and PCB pinout.drawio.svg||target="_blank"]]

13

14

(% class="wikigeneratedid" %)

15

This cable allows us to communicate with 4 chips using two data lines, audio & service switch, case switch and (yet to be documented) compute LEDs

= How we got here =

Measure out the ground and power signals by comparing with other chips on board. E.g. we find [SAA1064T] datasheet, locate the GND (Vee) and 5V (Vcc) and measure connectivity (0 ohm resistance) between chip pins and cable pins. This gives us pins GND 2 & 8 and PWR 16 & 22.

20

21

We keep doing this for SCL & SDA pins on SAA1064T chip and find pins 14 & 15 and 20 & 21 are I2C clock and data pins for each chip.

22

23

== Finding i2c chip address ==

=== SAA1064T ===

Reading the datasheet for SAA1064T chip we find that: "//This results in the corresponding valid addresses HEX 70, 72, 74 and 76 for writing and 71, 73, 75 and 77 for reading. All other addresses cannot be acknowledged by the circuit".// Giving us a clue what we are looking for, i2c addresses 0x70, 0x72 or 0x74.

=== PCA9554 ===

asdf

=== Code example finding i2c addresses ===

34

35

We can test the following addresses manually or use the following code snippet:

/*I2C_scanner

This sketch tests standard 7-bit addresses.

40

Devices with higher bit address might not be seen properly.*/

#include <Wire.h>

void setup() {

Wire.begin();

Serial.begin(9600);

while (!Serial);

Serial.println("\nI2C Scanner");

}

void loop() {

byte error, address;

int nDevices;

Serial.println("Scanning...");

57

58

nDevices = 0;

59

for (address = 1; address < 127; address++ ) {

60

Wire.beginTransmission(address);

61

error = Wire.endTransmission();

62

63

if (error == 0) {

64

Serial.print("I2C device found at address 0x");

65

if (address < 16)

66

Serial.print("0");

67

Serial.print(address, HEX);

68

Serial.println(" !");

nDevices++;

}

else if (error == 4) {

73

Serial.print("Unknown error at address 0x");

74

if (address < 16)

75

Serial.print("0");

76

Serial.println(address, HEX);

}

}

if (nDevices == 0)

Serial.println("No I2C devices found\n");

81

else

82

Serial.println("done\n");

delay(5000);

}

== i2c multiplexing with TCA9548 ==

89

90

We have two sets of chips, one for left and one for right where we have two different i2c chips on each side for controlling lights. Since the chips controlling their respective parts have the same address for each side, we can't distinguish them from each other. To handle this we use a i2c multiplexer to selectively communicate with one half at a time, switching TCA9548 between two different output ports.

91

92

=== Code example finding i2c ports ===

93

94

To verify wiring, connection, output ports and device addresses run the following script:

/**

* TCA9548 I2CScanner.ino -- I2C bus scanner for Arduino

99

*

100

* Based on https://playground.arduino.cc/Main/I2cScanner/

*

*/

#include "Wire.h"

#define TCAADDR 0x70

void tcaselect(uint8_t i) {

109

if (i > 7) return;

110

111

Wire.beginTransmission(TCAADDR);

112

Wire.write(1 << i);

113

Wire.endTransmission();

}

// standard Arduino setup()

void setup()

{

while (!Serial);

delay(1000);

Wire.begin();

Serial.begin(9600);

Serial.println("\nTCAScanner ready!");

127

128

for (uint8_t t=0; t<8; t++) {

129

tcaselect(t);

130

Serial.print("TCA Port #"); Serial.println(t);

131

132

for (uint8_t addr = 0; addr<=127; addr++) {

133

if (addr == TCAADDR) continue;

134

135

Wire.beginTransmission(addr);

136

if (!Wire.endTransmission()) {

137

Serial.print("Found I2C 0x"); Serial.println(addr,HEX);

}

}

}

Serial.println("\ndone");

}

void loop()

{

}

== SAA1064T data for driving center IO LED stack ==

150

151

Center IO stack is a stack of 24 LED's, 23 blue and 1 green for ethernet activity. These are duplicated next to each other and driven by each their SAA1064T chips. Earlier we found the i2c address and just by playing around figured out that 4 segments of 1 byte binary values are used to set ship register.

void fillColumns() {

Serial.println("filling columns");

156

Wire.beginTransmission(saa1064);

157

Wire.write(1);

158

Wire.write(0x7F); // 127 - 1111111

159

Wire.write(0x7F); // 127 - 1111111

160

Wire.write(0x7F); // 127 - 1111111

161

Wire.write(0x1F); // 31 - 11111

162

Wire.endTransmission();

colsFilled = 1;

}

(% class="wikigeneratedid" %)

169

~-~- Here the last byte we send only is 5 bits since we only have 5 LEDs instead of 6 to address (total of 24). Also note that we start the transmission with a single bit. ~-~-

170

171

== Pinouts voltages from MLB ==

Powered off:

* PWR fail LED - 0.00 V

176

* UID LED - 4.5V

177

* OH/Fan fail LED - 4.72 V

178

* NIC1 LED - 0.8 - 2.6 V

* NIC2 LED - 2.95 V

* UID SW - 2.8V

* HDD LED - 0.00 V

* Power LED P3V3 - 0.00V

183

* Power LED - 0.00 V after unplug grows

Powered on:

* PWR tail LED - 3.47 V

188

* UID LED - 4.85V

189

* OH/Fan failed LED - 5 V

190

* NIC 1 LED - 1.2 - 2.9 V

* NIC 2 LED - 3.2 V

* UID SW - 3V

* HDD LED - 3 V

* Power LED P3V3 - 3.30V

195

* Power LED - 0.87 V

196

197

= Controlling top I/O LED =

198

199

On the top row we have the following input/output devices in order from left to right;

Left side:

* physical lock

* lock LED

* warning/service button

206

* warning/service LED

207

* locate button

208

* power LED (red & green)

209

* fan LED (red & green)

210

* temperature LED (red & green)

211

* compute LED (unknown)

Right side:

* power LED (red & green)

216

* fan LED (red & green)

217

* temperature LED (red & green)

218

* compute LED (unknown)

219

* lock switch

220

221

Each sides bank of LEDs are driven by each their PCA9554 shift register. The registers represent the following LEDs: (Note that Lock LED is only present for the LEFT side)

222

223

(% border="1" %)

224

|=(% scope="row" %)Register|1|2|3|4|5|6|7

225

226

227

To control each LED we shift either a 0 to turn off or 1 to turn on. Since each device shares a single red/green LED (power LED green & power LED red) setting both to 1 at the same time will always leave it red. That is when power LED green and power LED red are both enabled, red always takes precedence.

228

229

Use following script to power LEDs one at a time:

230

231

232

#include <PCA9554.h> // Load the PCA9554 Library

233

234

PCA9554 ioCon1(0x24); // Create an object at this address

235

236