Front I/O
Pinout
There is a single cable that controls four parts, each half side of I/O LED and center column of blue LEDs.
Sub-paragraph
Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Excepteur sint occaecat cupidatat non proident, sunt in culpa qui officia deserunt mollit anim id est laborum.
Sub-paragraph
Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Excepteur sint occaecat cupidatat non proident, sunt in culpa qui officia deserunt mollit anim id est laborum.
Sub-sub paragraph
Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Excepteur sint occaecat cupidatat non proident, sunt in culpa qui officia deserunt mollit anim id est laborum.
How we got here
Measure out the ground and power signals by comparing with other chips on board. E.g. we find [SAA1064T] datasheet, locate the GND (Vee) and 5V (Vcc) and measure connectivity (0 ohm resistance) between chip pins and cable pins. This gives us pins GND 2 & 8 and PWR 16 & 22.
We keep doing this for SCL & SDA pins on SAA1064T chip and find pins 14 & 15 and 20 & 21 are I2C clock and data pins for each chip.
Finding i2c chip address
SAA1064T
Reading the datasheet for SAA1064T chip we find that: "This results in the corresponding valid addresses HEX 70, 72, 74 and 76 for writing and 71, 73, 75 and 77 for reading. All other addresses cannot be acknowledged by the circuit". Giving us a clue what we are looking for, i2c addresses 0x70, 0x72 or 0x74.
PCA9554
asdf
Code example finding i2c addresses
We can test the following addresses manually or use the following code snippet:
This sketch tests standard 7-bit addresses.
Devices with higher bit address might not be seen properly.*/
#include <Wire.h>
void setup() {
Wire.begin();
Serial.begin(9600);
while (!Serial);
Serial.println("\nI2C Scanner");
}
void loop() {
byte error, address;
int nDevices;
Serial.println("Scanning...");
nDevices = 0;
for (address = 1; address < 127; address++ ) {
Wire.beginTransmission(address);
error = Wire.endTransmission();
if (error == 0) {
Serial.print("I2C device found at address 0x");
if (address < 16)
Serial.print("0");
Serial.print(address, HEX);
Serial.println(" !");
nDevices++;
}
else if (error == 4) {
Serial.print("Unknown error at address 0x");
if (address < 16)
Serial.print("0");
Serial.println(address, HEX);
}
}
if (nDevices == 0)
Serial.println("No I2C devices found\n");
else
Serial.println("done\n");
delay(5000);
}
i2c multiplexing with TCA9548
We have two sets of chips, one for left and one for right where we have two different i2c chips on each side for controlling lights. Since the chips controlling their respective parts have the same address for each side, we can't distinguish them from each other. To handle this we use a i2c multiplexer to selectively communicate with one half at a time, switching TCA9548 between two different output ports.
Code example finding i2c ports
To verify wiring, connection, output ports and device addresses run the following script:
* TCA9548 I2CScanner.ino -- I2C bus scanner for Arduino
*
* Based on https://playground.arduino.cc/Main/I2cScanner/
*
*/
#include "Wire.h"
#define TCAADDR 0x70
void tcaselect(uint8_t i) {
if (i > 7) return;
Wire.beginTransmission(TCAADDR);
Wire.write(1 << i);
Wire.endTransmission();
}
// standard Arduino setup()
void setup()
{
while (!Serial);
delay(1000);
Wire.begin();
Serial.begin(9600);
Serial.println("\nTCAScanner ready!");
for (uint8_t t=0; t<8; t++) {
tcaselect(t);
Serial.print("TCA Port #"); Serial.println(t);
for (uint8_t addr = 0; addr<=127; addr++) {
if (addr == TCAADDR) continue;
Wire.beginTransmission(addr);
if (!Wire.endTransmission()) {
Serial.print("Found I2C 0x"); Serial.println(addr,HEX);
}
}
}
Serial.println("\ndone");
}
void loop()
{
}
